• Long-Reach End Mills McMaster-Carr

    These end mills have a long shank and a cutting edge that curves around the top of the ball end, allowing them to reach into pockets to create undercuts. Made of solid carbide, they are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Their extreme hardness means they are brittle, so a highly rigid setup

  • Extra Long Reach Ball End Mills Carbide End Mill Store

    End Mills > Ball Nose End Mills > X-Long Reach. Extra Long Reach Ball Nose End Mills. These mills are are often used in the mold industry where you need to reach into a pocket to mill and not hit the side wall. The have a stub lenth flute and a necked down diameter between the cutting edge and the shank.

  • 5/5(32)
  • Precision Twist EB6302V Carbide Ball Nose End Mill, Long

    Precision Twist EB6302V Carbide Ball Nose End Mill, Long Reach, TiAlN Multilayer Finish, 30 Deg Helix, 2 Flutes, 6" Overall Length, 1/2" Cutting Diameter,

  • Long End Mill Bits Long Length Carbide End Mill Store

    Long End Mills Carbide, Cobalt & HSS. These mills are used when you need a longer flute length than standard length end mills. They come in two, three, or four flute 30 degree helix geometries. They come as uncoated solid carbide or PVD AlTiN, TiCN, and ZrN coated. They are availe as square end, ball end,and er radius points.

  • 5/5(32)
  • Carbide Long Reach End Mills Results Page 1 :: Kaufman Co.

    HTC 13810.010" Diameter x .050" Length of Cut x .100" Reach Carbide Ball End Mill, 3 Flutes

  • Extra Extra Long Ball End Mills The Carbide End Mill Store

    These mills are general purpose carbide mills, with an extra extra long flute length (approx. 7+xD), two or four cutting edges, and a center cutting full radius or "ball" on the end. The term "general purpose" means that the flutes have a 30° helical spiral and the OD

  • Extra Long End Mills Carbide End Mill Store

    Extra Long End Mills Carbide, Cobalt & HSS. These mills are used when reaching deep inside a pocket to mill. They come in two or four flute 30 degree helix geometries. They come as uncoated solid carbide or PVD AlTiN and TiCN coated. They are availe as square end, ball end,and er radius points. They come in diameters from 1/8" to 1".

  • Amazon: Ball Nose End Mills: Industrial & Scientific

    SPEED TIGER ISB Carbide Ball Nose End Mill Micro Grain Carbide End Mill for Alloy Steels/Hardened Steels 2 Flute ISB5/16"2T Made in Taiwan (1 Piece, 5/16") 4.4 out of

  • Extra Extra Long End Mills-Square End-Carbide-General Purpose

    An extra extra long length square end mill is the longest flute length, single end, general purpose mill, where the ers are sharp and generate a 90° er. The term "general purpose" means that the mills are manufactured with a 30° helix angle, have a primary and secondary clearance angle on the OD's, and are center cutting. They can be used for plunging, grooving, side milling, face

  • Extra Long End Mills MSCDirect

    Shop a large range of extra long end mills at MSC Industrial Supply. MSC Industrial supply is here to support all your metaling and maintenance repair needs with over 1 million products in stock and ready to ship today!

  • Precision Twist EB6302V Carbide Ball Nose End Mill, Long

    Precision Twist EB6302V Carbide Ball Nose End Mill, Long Reach, TiAlN Multilayer Finish, 30 Deg Helix, 2 Flutes, 6" Overall Length, 1/2" Cutting Diameter, 1/2" Shank Diameter: Amazon:

  • Precision Twist EB6304V Carbide Ball Nose End Mill, Long

    YG-1 E5062 Carbide Ball Nose End Mill, Extra Long Reach, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 6" Overall Length, 0.25" Cutting Diameter, 0.25" Shank Diameter $80.63 Niagara Cutter N66226 Carbide Ball Nose End Mill

  • Amazon: extra long carbide end mills Ball Nose / End

    YG-1 E5014 Carbide Ball Nose End Mill, Long Reach, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 2.25" Overall Length, 0.125" Cutting Diameter, 0.125" Shank Diameter 5.0 out of 5 stars 3 Misc.

  • Carbide Long Reach End Mills Results Page 1 :: Kaufman Co.

    HTC 13810.010" Diameter x .050" Length of Cut x .100" Reach Carbide Ball End Mill, 3 Flutes

  • YG-1 E5014 Carbide Ball Nose End Mill, Long Reach

    The YG-1 E5014 uncoated carbide long-length ball nose end mill has two flutes and a 30-degree helix angle for machining on hardened and high-alloy steel, steel casting, chill casting, malleable cast iron,

  • 评论数: 3
  • Microcut Spherical Ball Carbide End Mills Long Reach

    Long & Extra Long Reach 2 and 4 Flute Spherical Ball Carbide End Mills AVAILABLE IN STANDARD LENGTH AND LONG SHANK SERIES DESIGNED FOR UNDERCUTTING & MACHINING MOLD