• Standard Length Ball End Mills

    These carbide ball end mills have a standard length flute (3xD), two or four cutting edges, and a center cutting full radius or "ball" on the end. The "general purpose" mills have flutes with a 30° helical spiral and an OD grind which has a standard primary and secondary clearance angle. The straight flute mills have no helix in the flute.

  • 5/5(32)
  • AlTiN Coated 2 Flute Standard Length Ball End Mills

    These carbide ball end mills are general purpose, with a standard flute length (3xD), two cutting edges, and a center cutting full radius or "ball" on the end. The term "general purpose" means that the flutes have a 30° helical spiral and the OD grind has a standard primary and secondary clearance angle.

  • 5/5(32)
  • 4 Flute Long Length Ball End Mills

    These carbide ball end mills are general purpose, with a long flute length (5xD), four cutting edges, and a center cutting full radius or "ball" on the end. The term "general purpose" means that the flutes have a 30° helical spiral and the OD grind has a standard primary and secondary clearance angle.

  • 5/5(32)
  • Spiral Flute Solid Carbide Thread Mills Regal Cutting Tools

    3 Flute Single End 45° Helix Ball Center Cutting Alu-Mill TC Carbide End Mill w/ TiCN Roughing Carbide End Mills 5 Flute Single End w/ flat 45° Helix Fine Pitch Center Cutting TC Carbide Roughing End Mill w/ TiCN

  • 4 Flute Extra Long Shank Ball End Mills

    End Mills > Ball Nose End Mills > X-Long Length > 4 Flute 40 Helix. 4 Flute Extra Long Shank Ball Nose End Mills. These mills are uniquely designed with long shanks and short flutes to reach into deep cavities. They are often used in the mold machining industry. They have 4 cutting edges, and a center cutting full radius or "ball" on the end.

  • 5/5(32)
  • Uncoated 4 Flute Stub Length Ball End Mills

    These carbide ball end mills are general purpose, with a stub flute length (1.5xD), four cutting edges, and a center cutting full radius or "ball" on the end. The term "general purpose" means that the flutes have a 30° helical spiral and the OD grind has a standard primary and secondary clearance angle.

  • Yonico 2-Flute Ball Nose Spiral End Mill 3/8 in. Dia 1/2

    This 2 flute round nose endmill has a cutting diameter of 3/8 in. and a cutting length of 1-1/16 in. The shank is 1/2 in. Dia and the overall length is 3 in. Ball nose spiral end mills are used for smooth

  • Yonico 2 Flute Upcut Spiral End Mill 1/8 in. Dia Solid

    Jan 23, 2020· Best used for: Standard milling, dadoing and boring. Cutting Diameter: 1/8 in. Cutting Height: 1/2 in. Shank Diameter: 1/4 in. Overall Length: 2 in. Flutes: 2 Up-cut end mills direct chips up and away from the milling area leaving an unobstructed path for the end mill. Bit breakage is less likely. Up cut end mills are the best cho for most standard milling

  • 1/4 in. Dia Solid Carbide 2-Flute Upcut Spiral End Mill 1

    Jun 16, 2020· Cutting Diameter: 1/4 in. Cutting Height: 1 in. Shank Diameter: 1/4 in. Overall Length: 2-1/2 in. Flutes: 2 Up-cut endmills direct chips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best cho for most standard milling

  • Spiral Flute Solid Carbide Thread Mills Regal Cutting Tools

    3 Flute Single End 45° Helix Ball Center Cutting Alu-Mill TC Carbide End Mill w/ TiCN Roughing Carbide End Mills 5 Flute Single End w/ flat 45° Helix Fine Pitch Center Cutting TC Carbide Roughing End Mill

  • Amazon: Ball Nose End Mills: Industrial & Scientific

    SpeTool 5PCS Ball Nose End Mill Cutter Router Bits Double Flute HRC55 Spiral Milling Tool 1/4 Inch Shank 2-1/2 Inch Length OVL 4.8 out of 5 stars 13 Misc.

  • Two-Flute End Mills McMaster-Carr

    When one end wears out, switch to the opposite end for two times the life of a standard carbide end mill. Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high